Flame Design (Pre-work for new mod)

[Malatory]

as life is subject to changes and so are the time lines of getting things done. So here it is another day and a little bit closer to getting done.

Darth Tater: RoboRator get our of my way you fool. I am the Master in this room.

RoboRaptor:<Sniff> <Sniff>

DarthTater: Look into my Eyes you mechanical slave. Chase down the little one in this house, get the cabbage patch doll and bring it to me.

RoboRaptor: Ding fries are done! Ding, Fries are done. <ROAR!>

Dath Tater: Augh! STOP that!

Ok back to work..

as you can see from the above pic, the flame lights up under the UV leds I have, But the UV Blue is not doing anything. That is the clear piece of acrylic that is infront of the flames.

I even had the quick chance to try out the light rod but it looks like it would be better for another color like blue

Little more detail can be found at malatorymods

[abnoea]

er.... darth tater loses i take it?

nice work...

[Malatory]

Ok I finally got to play with my new toy.. I need to work on cutting circles...

1st two are images of the fan cut out and the 2 sata ports w/molex power port. Still need to drill the holes for the screw to hold the SATA plugs in.

Closer look at the ports ... Not bad, sandable mistakes.

My helper today while I was working.
Future linux user with a robo rapture peeking over the edge of the rack.

abnoea:

They have not had a battle yet.

[Malatory]

OK update time ..

spent some time drilling holes and getting a few things lined up.

1st set should take any wondering out of the port issue.

Other side.

added some screws to the box. They will be used to hold everything together while welding the acrylic and If I have time I will replace them with clear acrylic screws.

The 50' of wire for the LED's (wont need all 50' but if ordering something always make sure you have enough .. Might have enought for 2-3 projects : ) )

Worked on the HDD cage part as well tonight.

start of drilling the holes

got the size for the HDD facing both ways .. Now I need to make them slide rails.

This is a sunbeam PCI Slot anyware add on. Will be used in the Spider case but right now I am using the HDD part to make sure the holes line up on the acrylic

Yet another image of it.

I have also sanded down the flames edges once again seeing I need to weld them to the clear acrylic and then polish them up. This should keep it from crazing.

[Malatory]

ok more work done. Not all today but with whats been going on, today is really the 1st time I had to get the pics taken and off the camera.

1st off this last weekend I welded the flames to the clear acrylic (thinking I went a little light on the weldon).

Next I also cut out the rails for the HD cage and used some old HDD to make sure things squared up.

I also added in a 120MM fan and fan gril that I have to make sure things are lining up right.

[Malatory]

OK here is the update with pics.

I reassimbled the box today and did a test fitting of all of the peices together. I realized that I am very tight in the case. I also make the screw holes from the back & front pannel, as well as the ones to hole the HDD cage. Removed some of the protective covering to see how it looks.

So more pics of the fan that matches the flames that I have as well as the fan grill.

In the next few days I will be taking the HDD thats in the Laureate HDD drive cage. As it is my spare SATA drive. Used for reveiws and testing projects not.

Starting the like the way things are unfolding on this, as I would say I am close to 90% done if not more.

[Rankenphile]

looking good! I would recommend finding a way to attach or run the cables in the box along one of the corners and up to the plugs/ports, so that they are not just loose inside there, but that's not really a criticism at all. Everything looks absolutely fantastic. Keep it up!

[Malatory]

looking good! I would recommend finding a way to attach or run the cables in the box along one of the corners and up to the plugs/ports, so that they are not just loose inside there, but that's not really a criticism at all. Everything looks absolutely fantastic. Keep it up!

You have to remimber that those drives are old PATA drives and I havn't placed the power cable and done any cable management yet.

Heck there is still blue painters tape inside there keeping thing protected from scraches.

[public_eyesore]

nice

[Malatory]

OK yet another weekend and another update .. FINISHED !!!! Yeah!!!! Time to enter it into a few contest (TGS Case give away for one).

Front of the case

Side View:

Top: UV Only

What I did today:
Wired all of the UV led's (minus the fans), shorttened and converted the Molex plugs to SATA
Added Power port for the Fan & LED's
Drilled out the Air hole on the Back port for air flow.

replaced the test drives with a real SATA drive.