Results 1 to 9 of 9

Thread: What do I need to do this?

  1. #1
    One Eye, Sixteen Cores. Kayin's Avatar
    Join Date
    Jun 2009
    Location
    Birmingham, AL
    Posts
    1,921

    Default What do I need to do this?

    All right, so I have a fair few of the parts I need. I have the speakers I need for my PC front, I have a Jupiter Electronics voice box, and I have a lot of wire. What I need to do is to set up the speakers in such a way that the voice box lights up when they play sound. I can do the individual sound card set ups as well as the PC automation stuff, but the signal from my line out isn't strong enough to trip my voice box. Do I need an amp, will it hurt my laptop speakers (literally from a laptop, Toshiba Satellite, brand new machine destroyed by someone's stupidity) and if so, where to find it? I can handle solder it yourself stuff just fine. Just need to know what I need here. For comparison purposes, the voice box I have is normally run by a car stereo system. So I'm guessing that it needs some amping. The maker said that he'd had luck from people off their PC sub, but KITT's voice is rather high. The front setup will only be used to play voice clips, so there won't be a sub at all.

    Help me Obi-Wan Kenobi, you're my only hope (in a manner of speaking.)
    Project:Mithril, sponsored by Petra's Tech Shop and Sidewinder Computers-MOTM Nominee October '08




  2. #2
    Moderator TLHarrell's Avatar
    Join Date
    Jan 2012
    Location
    Morgan Hill, CA
    Posts
    1,143

    Default Re: What do I need to do this?

    I have a hammer! I can put things together! I can knock things apart! I can alter my environment at will and make an incredible din all the while! -Calvin

  3. #3
    Anodized. Again. Konrad's Avatar
    Join Date
    Aug 2010
    Location
    Canada
    Posts
    1,060

    Default Re: What do I need to do this?

    Just use a generic transistor amp circuit with the correct voltage bias for the speakers. If Toshiba Satellite uses standard mini 5V/8Ω magnetic loudspeakers they'll require a bit of signal drive (~3W for the pair) and be able to tolerate momentary overwattage without being damaged/derated. If they're piezo speakers then you'll need to be a little more careful not to overload them. Otherwise, just fiddle with resistor and diode values until you get reasonable maximum volume/light level.

    Another good option would be to use an audio amp circuit based around some kind of LM386 part. Gain is respectable and distortion isn't very relevant in this application.

    These sorts of little parts will probably outlast the LEDs and generate inconsequential heat. You could use an electromechanical relay instead, but it's less efficient, fugly, probably won't last as long, and the constant click-click switching on a direct-audio signal would probably be really annoying.

    I realize you want lights, not sound ... but unless you can adjust the sensitivity on whatever sensor part your LED driver circuit uses, it's probably easiest to just feed it exactly the sort of audio intensity it was built to detect.
    My mind says Technic, but my body says Duplo.

  4. #4
    Moderator TLHarrell's Avatar
    Join Date
    Jan 2012
    Location
    Morgan Hill, CA
    Posts
    1,143

    Default Re: What do I need to do this?

    Found the post I had seen about this in my bookmarks at work.

    http://www.adafruit.com/blog/2012/04...ut-led-driver/
    I have a hammer! I can put things together! I can knock things apart! I can alter my environment at will and make an incredible din all the while! -Calvin

  5. #5
    ATX Mental Case Crimson13's Avatar
    Join Date
    Nov 2005
    Location
    Northern, IL, USA
    Posts
    137

    Default Re: What do I need to do this?

    There's also this: http://www.sparkfun.com/products/10468

    It outputs DC so it might give the effect you're looking for.

  6. #6
    Moderator TLHarrell's Avatar
    Join Date
    Jan 2012
    Location
    Morgan Hill, CA
    Posts
    1,143

    Default Re: What do I need to do this?

    LOL! Take a look right below the product photo thumbnails. See the link for ASCII Version? Click on it. Awesome.
    I have a hammer! I can put things together! I can knock things apart! I can alter my environment at will and make an incredible din all the while! -Calvin

  7. #7
    One Eye, Sixteen Cores. Kayin's Avatar
    Join Date
    Jun 2009
    Location
    Birmingham, AL
    Posts
    1,921

    Default Re: What do I need to do this?

    The voice box has an LM3915M on board. I need to boost the input power to it without ruining my tiny but rather powerful speakers.

    I'm starting to wonder if a DIY headphone amp wouldn't work.
    Project:Mithril, sponsored by Petra's Tech Shop and Sidewinder Computers-MOTM Nominee October '08




  8. #8
    Moderator TLHarrell's Avatar
    Join Date
    Jan 2012
    Location
    Morgan Hill, CA
    Posts
    1,143

    Default Re: What do I need to do this?

    Split the audio signal up and send part of it through a transistor to the voice box trigger. Apply voltage to the switched side of the transistor as needed to get to your trigger voltage.
    I have a hammer! I can put things together! I can knock things apart! I can alter my environment at will and make an incredible din all the while! -Calvin

  9. #9
    One Eye, Sixteen Cores. Kayin's Avatar
    Join Date
    Jun 2009
    Location
    Birmingham, AL
    Posts
    1,921

    Default Re: What do I need to do this?

    That I can do. Now, to draw up the board I'll need for all this stuff...
    Project:Mithril, sponsored by Petra's Tech Shop and Sidewinder Computers-MOTM Nominee October '08




Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •